Fire Alarm Control Panels
F100A
Analogue addressable fire alarm control panel with 2 to 4 loops and 2 x 40-character back-lit LCD display
F16e
Conventional fire alarm control panel with 8 to 32 zones. Available in NZS 4512:2010 and NZS 4512:1997 versions
F4-3
Four-zone conventional fire alarm control panel. Complies with NZS 4512:2010 requirements. Easily configured for NZS 4512:1997 compliance
F1-3 Fire Alarm Control Panel
Single-zone conventional fire alarm control panel. Complies with NZS 4512:2010 requirements. Easily configured for NZS 4512:1997 compliance
F4AUXRLYV2 Relay Board
Provides additional (auxiliary) fire and fault (defect) relays for an F4 conventional fire alarm control panel
F220
Analogue addressable fire alarm control panel with seven-inch 800 x 480 pixel TFT LCD colour display and up to 20 loops
Networking
NETCARD Network Card
Network card for interfacing F100 and F120 control panels, and other networkable devices, with a Pertronic F100/F120 Network System
SysLogCopier
Copies Linux OS diagnostic logs from F220 or Net2 card to USB stick. This tool is also available in Pertronic FireUtils® v7.00 (or later)
RS485REP Repeater
Provides bi-directional half-duplex communication between a Master RS-485 port and up to 5 electrically separate Slave ports
Net2LayoutTool
A free software tool that automatically creates a data table representing the layout of an F220/Net2 network
NET2-EMM Mini-Mimic
Remote display for an F220 Net2 system. Programmable to monitor selected zones, F220 panels, or the entire network
F220
Analogue addressable fire alarm control panel with seven-inch 800 x 480 pixel TFT LCD colour display and up to 20 loops
Net2 Network
Networking system for F220 fire alarm control panels. Fault-tolerant. Adaptive messaging. Native interfaces for BMS (Modbus) and FireMap
NET2 Network Card
F220/Net2 Network node. Connects an F220 fire panel to Net2 Network Ring Circuit. May be configured as a BMS (Modbus) or FireMap interface
NET2-NCU Control Unit
Remote control and monitoring of an F220 Net2 network system. Programmable to control selected F220 fire panels or the entire network
NET2-AMM Mini-Mimic
Remote display of Alarm & Evacuate signals from F220 Net2 system. Programmable to monitor selected zones, F220 panels, or the entire network
F100A
Analogue addressable fire alarm control panel with 2 to 4 loops and 2 x 40-character back-lit LCD display
Software Applications
FireMap Graphics
Fire system management tool (GUI). In the event of an alarm, FireMap automatically displays a map showing the location of the alarm source
FireMap Gateway
Interface card for connecting Pertronic FireMap to a Pertronic analogue addressable fire panel via Ethernet
FireUtils v7.06.01
Free Windows-compatible programming and diagnostic application for F220/Net2 systems. Also supports F120A
F100A Utilities v5.14.04
F100A fire system programming and diagnostic application for F100A version 5.xx.xx
Network Utilities v2.14.08
Network system programming and diagnostic application for the Pertronic Network
F100A Utilities v3.24.4
F100A fire system programming and diagnostic application for F100A v3.xx.xx - v4.58
F100A Utilities v2.14
F100A fire system programming and diagnostic application for F100A v1.65 - v2.xx.xx. (Prior to introduction of Boolean cause-effect logic)
F100A TMS Utilities v2.1
F100A TMS fire system programming and diagnostic application for all F100A TMS versions
VESDA VSC v3.12
Management application for Xtralis fire and gas detection systems including VESDA and ICAM smoke and gas detectors and ancillary devices
VESDA Aspire Software v3.12
A Windows®-based application for designing and specifying VESDA aspirating smoke detection systems
FireMap Pager
Messaging interface for Pertronic FireMap® graphic user interface. Initiates email or pager messages as defined in pre-configured rules
FAAST FLEX Aspire v3.10
Windows® app. for designing and specifying FAAST FLEX ASD systems including pipe network configuration. NOTE: Does not support VESDA systems
FAAST PipeIQ v3.0.0
A Windows®-based application for designing and specifying FAAST aspirating smoke detection systems
Extinguishing Agent Release Systems
Extinguishing Agent Release Panels
Control panels for extinguishing agent release (fire suppression) systems including gas flood, water deluge, and foam deluge
Solenoid Interface
Interface units which allow allow analogue addressable control modules to activate and supervise a wide range of solenoids
ACS2 Agent Control Station
Pertronic agent release system must include one Agent Control Station. It's available in flush-mount or surface-mount configuration
LCS2 Local Control Station
Pertronic agent release system may include up to nine Local Control Stations. It's available in flush-mount or surface-mount configuration
ARC2 Agent Release Controller
The ARC2 is the central component of the Pertronic Extinguishing Agent Release System. It's designed to control gas flood equipment
Equipment Cabinets
Mimics, Repeaters & Interfaces
FireMap Gateway
Interface card for connecting Pertronic FireMap to a Pertronic analogue addressable fire panel via Ethernet
F100A LCD Mini Mimics
LCD mini-mimic remote display for Pertronic F100A & F120A analogue addressable fire alarm control panels
SPIB Text Interface
Interface for printers, pagers, nurse-call pagers, and other text systems. Automatically exports selected event data as a serial text stream
F100A LCD & LED Combination Mimics
F100A combination mimic with LED display and integral mini-mimic. Available in three sizes. Front and rear service variants
LED Display Boards
LED display boards for Pertronic fire alarm systems including F100, F120, and F16e
L485 LED Address Controller
Controller for driving multiple LEDs, relays, or open collector outputs from a Pertronic fire alarm control panel's RS-485 bus
F4-RMAX Module
Interface for connecting a remote LED mimic to an F4 fire alarm control panel. With auxiliary fire and auxiliary fault (defect) relays
RS485REP Repeater
Provides bi-directional half-duplex communication between a Master RS-485 port and up to 5 electrically separate Slave ports
SGDAP
Signal Generating Device (Advanced Protocol) for interfacing F100A, F220, and F120A fire panels with fire brigade alarm transmitters
SGD7 Signal Gen
Digital Signal Generating Device for interfacing a fire alarm system with a fire brigade alarm transmitter
SGD8MD Multidrop
Two-Wire Multidrop Digital Signal Generating Device for interfacing a fire alarm system with a fire brigade alarm transmitter
SPIB-MODBUS HLI Interface
Bi-directional Modbus interface for connecting a F220 FACP with one or more Modbus master devices such as a Building Management System (BMS)
NET2-EMM Mini-Mimic
Remote display for an F220 Net2 system. Programmable to monitor selected zones, F220 panels, or the entire network
CLC-MON-N9P Cable
Flexible RS-232 extension lead with DB9 male and DB9 female connectors and straight-through connection
F220-FFM Mimic
Provides full remote control and monitoring of an F220 fire panel, for systems that need control at multiple locations.
F220-AMM Mini-Mimic
Remote display of Alarm and Evacuate signals from an F220 fire panel. For use by staff who are expected to respond to alarms.
NET2-NCU Control Unit
Remote control and monitoring of an F220 Net2 network system. Programmable to control selected F220 fire panels or the entire network
NET2-AMM Mini-Mimic
Remote display of Alarm & Evacuate signals from F220 Net2 system. Programmable to monitor selected zones, F220 panels, or the entire network
F220 LCD & LED Combination Mimics
F220 combination mimic with LED display and F220 alarm mini-mimic. Available in three sizes. Front and rear service variants
Transmitters
SGDAP
Signal Generating Device (Advanced Protocol) for interfacing F100A, F220, and F120A fire panels with fire brigade alarm transmitters
SGD7 Signal Gen
Digital Signal Generating Device for interfacing a fire alarm system with a fire brigade alarm transmitter
SGD8MD Multidrop
Two-Wire Multidrop Digital Signal Generating Device for interfacing a fire alarm system with a fire brigade alarm transmitter
Accessories
CCCI Interface
It's suitable for use with the F16e, F16, F4, or F1 panels, or with Loop
Responders on analogue addressable systems.
Responders on analogue addressable systems.
SPIB Text Interface
Interface for printers, pagers, nurse-call pagers, and other text systems. Automatically exports selected event data as a serial text stream
FINDER12.21.0.024 Time Clock
Seven-day timer with single channel form C (change-over) relay output
F4-RMAX Module
Interface for connecting a remote LED mimic to an F4 fire alarm control panel. With auxiliary fire and auxiliary fault (defect) relays
SGDAP
Signal Generating Device (Advanced Protocol) for interfacing F100A, F220, and F120A fire panels with fire brigade alarm transmitters
CPPFPL Mounting Plate
Fascia panel for flush-mounting Pertronic Manual Call Points in place of large old manual call points (break-glass alarms)
CPTSTPRHTR Call Point Stopper
A tough, transparent, polycarbonate shield and frame that fits over a manual call point, with built-in 230 Vac heater
SPIB-MODBUS HLI Interface
Bi-directional Modbus interface for connecting a F220 FACP with one or more Modbus master devices such as a Building Management System (BMS)
F4AUXRLYV2 Relay Board
Provides additional (auxiliary) fire and fault (defect) relays for an F4 conventional fire alarm control panel
In-Ceiling Detector Mount Kit
Kit of parts for mounting a point detector in a ceiling space.
CPTST series
A tough, transparent, polycarbonate shield and frame that fits over a manual call point. Fitted with warning sounder
KACSGW MCP Window
Replacement windows for Manual Call Points, including Snapglaze and Break-Glass types
F100ZIPB Opto-Isolated IP Board
Eight-way opto-isolated input board for the Pertronic analogue addressable loop responder and multi-function loop responder
MOXA-TCF-142 Series
MOXA serial to fire-optic converters for RS-232 and RS-485 circuits. Transmit up to 40 km over single-mode fibre-optic cable
RLY24V Relay
Auxiliary relay board with two form C (changeover) contacts rated 4 Amps, 30 Vdc (resistive). 24 Volt (nominal) coil
SBB-L
Surface-mounting back boxes for L Series alarm (alerting) devices. Available in wall-mount and ceiling-mount variants.
MOXAK Ethernet Module Kit
Moxa serial to Ethernet interface kit with lead & null modem cable
CPTST Weatherproof
A tough, transparent, weatherproof polycarbonate shield and frame that fits over a manual call point
CLC-MON-N9P Cable
Flexible RS-232 extension lead with DB9 male and DB9 female connectors and straight-through connection
Tools and Test Equipment
OSID Laser Tool
This tool clips into the eyeball on OSI/OSID beam smoke detectors. It produces a red laser beam showing the detector beam's target