F220 Fire Panels
F220
The Pertronic F220®, a modular, expandable, networkable, intelligent fire panel displays the exact location of any alarm or other signal activation in a user-friendly format.
F220-ARC
The Pertronic F220 Extinguishing Agent Release System provides automatic control of one or more fire suppression systems.
F220-Net2 Network
NET2
The Pertronic F220-Net2 Network connects multiple fire panels, Net2 Network Control Units (Net2 NCU) and Net2 remote displays into a single fault-tolerant system.
NET2CARD
As the central building block for the Pertronic F220-Net2 Network System, the Net2 Network Card may be configured to interface with a number of devices.
FIBNET
Pertronic Net2 Fibre Optic Converters (FIBNET) provide dual fibre-optic network ports for the Pertronic Net2 Network Card (NET2CARD).
RS485 Repeater
The RS-485 Repeater/Splitter creates electrically separate RS-485 segments, with bi-directional half-duplex communication between a master RS-485 and up to five repeater ports.
Analogue Addressable Detectors
2251BPI
The Analogue Addressable Smoke Detector (2215BPI) is a plug-in photoelectric unit, where sensor chamber smoke levels are continuously monitored and reported to the fire panel.
2251CTLE
This 200 Series intelligent plug-in COPTIR fire sensor combines CO fire monitoring, IR for measuring ambient light levels and flame signatures, optical smoke and heat detection.
22051TLE
This analogue addressable PTIR (Photoelectric, Thermal, Infra Red) Multi-Criteria smoke detector combines three sensing elements in one unit.
5251BPI
The 5251BPI point-type heat detector has either a fixed (static) alarm threshold, or rate-of-rise (ROR) alarm threshold; continually reporting this temperature measurement to the fire panel.
5251RBPI
The 5251RBPI point-type rate of rise heat detector automatically initiates an alarm condition for a pre-configured rapid temperature increase.
B524IEFT-1
This is a detector base designed for use with System Sensor analogue addressable detectors. It prevents an entire communications loop from being disabled when a short-circuit occurs.
B501AP
Plug-in base for AA detectors and loop devices; deeper than the standard B501AUS. Suitable for VAD and WST series strobes, WSS-sounder strobes, BSO-sounders, and BSS-sounder strobes.
WB-1AP-IV
For high humidity environments (which may cause nuisance alarms), System Sensor has this molded plastic enclosure kit for detector adapter bases in order to minimise condensation effects.
CP500 Programmer
A handheld programmer to read and set the address for System Sensor analogue addressable detectors, modules, callpoints and Spectralert horns/strobes.
I/F for PWF 8000 LHD
The Pertronic SPIB-PWF8000 connects a Protectowire Fibre System 8000 with a Pertronic F220 fire system using the panel's loop emulation capability.
5251CPI Detector
As C series intelligent addressable heat detectors continually reporting to the fire panel, they have a fixed temperature alarm threshold (5251CPI or rate-of-rise alarm (5251RCPI).
5251RCPI Detector
This rate-of-rise (ROR) detector is pre-configured, continually reports temperature measurement to the fire panel, and sends an alarm signal if it rapidly increases.
2251CPI Detector
The 2251CPI C Series smoke detector in an improved version of the 2251BPI intelligent addressable photoelectric model, featuring a smoke sensing chamber which diminishes nuisance alarms.
Conventional Detectors
2151BPI
This photoelectric point detector is designed for general purpose smoke detection in conventional circuits. It features an on-board signal processor designed to reduce nuisance alarms.
WB-1AP-IV
For high humidity environments (which may cause nuisance alarms), System Sensor has this molded plastic enclosure kit for detector adapter bases in order to minimise condensation effects.
5151 Series
As 2-wire heat detectors, the System Sensor 5151 Series II range combines rate-of-rise and fixed temperature operations to provide open-area protection. They comply with AS 7240.5-2004.
B401
The B401 plug-in detector base is used with numerous System Sensor smoke and heat detector heads, and is much more versatile than equivalent direct-wired models.
B401R
The B401R plug-in detector base is used with a System Sensor model 2451E photoelectric head and 1451E ionization head, and also contains a resistor to provide current limiting in the alarm state.
885-WP
This weatherproof heat detector is a conventional rate-of-rise heat detector, plus 60 degree C fixed temperature threshold, designed to provide open area protection in areas subject to moisture.
Manual Call Points
WCP5A
Suitable for use in most exterior environments, the weatherproof AA Manual Call Point (WCP5A) is a sealed addressable unit ('break glass') for manually raising an alarm on Pertronic AA fire systems.
MCP3A Red
The MCP range provide a 'plug and play' concept to reduce installation time. All initial installation is in a special terminal block which is then simply connected to the back of the MCP.
WCP3A
As an IP67 sealed product the Weatherproof Conventional Manual Call Point (WCP3A), the unit can be installed in many external environments where water and dirt are likely to be present.
PS200 FLAP
This transparent plastic flap means a MCP can only be operated when the flap is lifted up. It is particularly useful in high traffic areas, such as school and public building stairwells and corridors, with a significant chance of accidental MCP operation.
MCP4A
The MCP4A is a yellow 'Gas Release' manual call point. It is a 'plug and play' unit with all initial installation finishing in a special terminal block, and this block simply connecting to the back of the MCP.
KG1
Replacement break glass window for Manual Call Points. The KG1 fits System Sensor M400KA and M500k MCPs, and all KAC MCPs.
MCP5A
This AA MCP has a flexible plastic activating panel, which when pressed slides downwards activates an internal switch, triggering the alarm signal. A supplied test key also triggers the alarm.
SC070 Key
A test key allowing technicians to test KAC MCPs (triggers an alarm condition) without breaking or flexing the operating element. The key's other end also fits System Sensor M500K and M400KA call points.
Duct Detectors
DNR-AUS
This non-relay photoelectric smoke detector's pivoting housing is capable of mounting to a round or rectangular duct. Smoke can be sensed in 0.5m-20m/sec airflow, between -20 to 70 degrees C.
DNRW
The weatherproof version of the InnovairFlex Intelligent Photoelectric Duct Smoke Detector. For extreme environments like rooftops, the DNRW can be installed without a costly enclosure.
D2-AUS
A 2-wire InnovairFlex duct smoke detector, isolates the sensor head from the LowFlow feature for simple maintenance. The housing has a 20mm conduit knockout and ample wiring space.
D4120
A 4-wire photoelectric duct smoke detector, with an easy-access Test/Reset. Its three DIP switches can be used to configure field selectable settings. Can be customised to local codes.
Sampling Tube
Sampling tubes, which may be cut to length as necessary, for use in DNR, DNRW, D2 and D4120 Photoelectric Duct Detectors.
Beam Detectors
Flame Detectors
Aspirating Smoke Detection
Modules
Accessories
SC070 Key
A test key allowing technicians to test KAC MCPs (triggers an alarm condition) without breaking or flexing the operating element. The key's other end also fits System Sensor M500K and M400KA call points.
CP500 Programmer
A handheld programmer to read and set the address for System Sensor analogue addressable detectors, modules, callpoints and Spectralert horns/strobes.
